Skip to guide
User Manual
EN

Interactive user guide

Harmony A3 Setup Guide

Connect one source. Play it through your powered speakers.

Follow four steps to connect the Harmony A3 transmitter and three AuraLink receivers.

Start SetupFix a problem
1

Connect power

  1. Connect the transmitter to power with a USB-C cable and power adapter.
  2. Switch the transmitter to ON.
DoneThe transmitter indicators turn on.
If notReseat the power cable.Still off? Try another power adapter and outlet.
2

Choose your source

Choose the device that sends audio to the transmitter.

3

Connect Optical

TV / Media Device

  1. Short-press AUX/OPT once on the transmitter to select OPT input.OPT indicator: blinking red.
  2. Remove the clear caps from both ends of the optical cable.
  3. Connect Optical Out on the TV/source to Optical on the transmitter.
  4. On the TV/source, select Optical output and set the format to PCM.
    ✓PCM
    ✕Dolby / DTS / Bitstream / Auto — No sound.
DoneThe audio indicator responds and listeners hear the TV audio.
If notPort: use Optical Out, not In.Format: select PCM.
Not sure how to set PCM?Open the Brand-by-Brand TV Guide →
Source connected — next: Step 4
3

Connect analog audio

Mixer / AV System

Choose the correct output and cable. The wrong cable may cause low volume, missing vocals, or poor sound quality.
  1. Confirm AUX inputThe transmitter starts in AUX input mode. Confirm the AUX indicator is blinking red.If not, short-press AUX/OPT once.
  2. Check the source outputLook for XLR, 6.35 mm, RCA, or 3.5 mm output ports.
  3. Choose your outputSelect the matching option below.

How many XLR outputs will you use?

Dual XLR Output

  1. Use a dual XLR female-to-unbalanced 3.5 mm TRS cable.Wrong cable? It may cause low volume or missing vocals.
  2. Connect the XLR plugs to mixer Output L / R.
  3. Connect the 3.5 mm plug to the transmitter AUX In.
Mixer OUTPUT L / RDual XLR female-to-3.5 mm TRS cabletransmitter AUX IN
Dual XLR mixer outputs connected to transmitter AUX In
The transmitter rear panel; the AUX input is the second port from the left

Stereo mixer output recommended

Done: the transmitter audio indicator responds and listeners hear clear stereo audio.
If not:
  1. Check both plugs are in mixer Output L / R.
  2. Unmute the mixer output.
  3. Lower the mixer level.
Cable not included. Buy separately if needed →
Source connected — next: Step 4

Single XLR Output

  1. Use a single XLR female-to-unbalanced 3.5 mm TRS cable.Mono output: A single XLR carries mono audio.
    Wrong cable? It may cause low volume or poor sound quality.
  2. Connect the XLR plug to the mixer Output.
  3. Connect the 3.5 mm plug to the transmitter AUX In.
Mixer OUTPUTSingle XLR female-to-3.5 mm TRS cabletransmitter AUX IN
Single XLR mixer output connected to transmitter AUX In
The transmitter rear panel; the AUX input is the second port from the left

Mono output only

Done: the transmitter audio indicator responds and listeners hear the mono source audio.
If not:
  1. Check the cable is unbalanced 3.5 mm TRS.
  2. Use a mixer output jack.
  3. Unmute the mixer output.
Cable not included. Buy separately if needed →
Source connected — next: Step 4

6.35 mm Output

  1. Use the included dual 6.35 mm-to-3.5 mm cable.Wrong cable? It may cause poor sound quality.
  2. Connect the two 6.35 mm plugs to mixer Output L / R.
  3. Connect the 3.5 mm plug to the transmitter AUX In.
Mixer OUTPUT L / RDual 6.35 mm-to-3.5 mm cabletransmitter AUX IN
Dual 6.35 mm mixer outputs connected to transmitter AUX In
The transmitter rear panel; the AUX input is the second port from the left

Stereo mixer output recommended

DoneThe audio indicator responds and listeners hear clear stereo audio.
If not:
  1. Connect both plugs to Output L / R.
  2. Unmute the mixer output.
  3. If sound is distorted, lower the source level.
Source connected — next: Step 4

RCA / 3.5 mm Output

Choose the matching output. Connect only an audio output to the transmitter AUX In.
RCA Output

Connect RCA Out to the transmitter AUX In with an RCA-to-3.5 mm cable.

Source RCA OUT L / RRCA-to-3.5 mm cabletransmitter AUX IN
RCA left and right outputs connected to transmitter AUX In
The transmitter rear panel; the AUX input is the second port from the left
RCA cable not included. Buy separately if needed →
3.5 mm Output

Connect 3.5 mm Out to the transmitter AUX In with the included 3.5 mm-to-3.5 mm cable.

Source 3.5 mm OUT3.5 mm-to-3.5 mm cabletransmitter AUX IN
3.5 mm audio output connected to transmitter AUX In
The transmitter rear panel; the AUX input is the second port from the left
DoneThe audio indicator responds and listeners hear clear audio.
If not:
  1. Use an audio output, not an input.
  2. Unmute the source.
  3. Raise the source volume gradually.
Source connected — next: Step 4
3

Connect with Bluetooth

Phone / Tablet / Computer

Keep your phone close to the transmitter while pairing.

  1. Start pairing: Short-press Phone/Pair once on the transmitter.The transmitter's Phone light: blinking red and blue.If not, press and hold Phone/Pair.
  2. Connect your source: open Bluetooth settings and select the transmitter.
  3. Play audio on the phone, tablet, or computer.
Keep the phone near the transmitter rather than in a pocket while pairing
For a better experience: use a wired audio input for best stability.Bluetooth range: approximately 10–15 m (30–50 ft).
DoneThe audio indicator responds and listeners hear the source audio.
How It Works: Bluetooth sends audio to the transmitter. Listeners receive it through Auracast.
If not

The transmitter not listed?

  1. Turn off Bluetooth on the previous source.
  2. Start pairing again.
  3. Move the devices closer.
Source connected — next: Step 4
4

Play audio through your speakers

First: choose and connect your audio source (Steps 2–3).

Requires: One powered speaker with a 3.5 mm AUX or RCA input per receiver. Passive speakers need an amplifier.

  1. Turn on each AuraLink receiver. Its Auracast light turns solid orange when connected.
  2. Connect each receiver to a powered speaker's AUX or RCA input using the matching cable.
  3. Turn on each powered speaker and play audio from your source.

Video: turn on the receivers and connect them to powered speakers.

Done

All three receivers show solid orange; every connected speaker plays the audio.

If not

Light blinking orange? Move the receiver closer to the transmitter.

Light solid, no sound? Check the cable and volume. Check the speaker's AUX setting ↓

Still no sound? Fix a problem →

Placement

Placement tips

Transmitter

  • Place in the center.
  • Clear line of sight.
  • Up to 330 ft.

Phone

  • Keep next to transmitter.
  • Do not keep in pocket.
Correct: keep the phone next to the transmitterIncorrect: do not keep the phone in a pocket

Optional expansion

Add powered speakers

To add another powered speaker, connect a compatible AuraLink receiver to its AUX or RCA input and join the same Auracast broadcast. Check for audio at the new speaker.

View AuraLink receiver

Receiver reference

Power and use an AuraLink receiver

Charge an AuraLink receiver

Use USB-C and a 5 V, 1–2.4 A power source. The receiver works while charging and plays for up to 20 hours.

  • Blinking red: low battery.
  • Solid red: charging.
  • Red light off: fully charged.

Turns off after 15 minutes without audio? Older firmware can do this even while plugged in. Check the Harmony A3 firmware page for an update.

Play phone audio through an AuraLink receiver
  1. Hold the AuraLink receiver's multifunction button for 3 seconds. Its light blinks red and blue.
  2. On your phone or tablet, select AuraLink in Bluetooth settings.
  3. Play audio through the connected powered speaker.

Audio only: phone calls are not supported. Bluetooth audio takes priority; Auracast resumes when Bluetooth audio stops.

Firmware update

Update Harmony A3

Update the AuraLink receivers and transmitter. The firmware page lists the transmitter as Oasis Aura.

Update AuraLink receivers

Update each receiver separately, one at a time.

  1. Download the Firmware Update Tool.

  2. Connect one AuraLink receiver to your computer.

    Firmware update cable: Use the gray USB data cable included with Harmony A3.

    Mac users: use the same included gray USB data cable.

  3. Run the updater.

    Follow its instructions and keep one AuraLink receiver connected until the update is complete.

After updating, reset each receiver.

Update the transmitter

  1. Download the Firmware Update Tool.

  2. Connect the Harmony A3 transmitter to your computer.

    Firmware update cable: Use the gray USB data cable included with Harmony A3.

    Mac users: use the same included gray USB data cable.

  3. Run the updater.

    Follow its instructions and keep the Harmony A3 transmitter connected until the update is complete.

After updating, reset the transmitter.
Open Harmony A3 firmware page Notify me about updates

PC tool · Optional

Change advanced broadcast settings

Connect the Harmony A3 transmitter to your computer. Open the Firmware Update Tool and select Advanced.

Example Oasis Aura Firmware Update Tool screen. Select the image to enlarge.

Firmware Update Tool Advanced screen showing audio mode, broadcast name, encryption, default volume, QR code, and receiver synchronization controls
Rename the broadcast
Change the name listeners see when they search for Harmony A3.
Encrypt the broadcast
Add a passcode so only listeners with the correct code can join.
Set the default volume
Adjust the transmitter's default broadcast volume.
Change the audio mode
For listeners using compatible hearing aids, select Hearing Aid Compatible and apply the settings. Continue to the hearing-aid joining guide →
Generate a broadcast QR code
Create a QR code for joining the broadcast.Requires: compatible hearing aids and an app that supports joining by QR code.
Use Group Settings
Apply the same broadcast name and passcode to multiple supported receivers. Learn about Group Settings →

Optional listening method

Listen from hearing aids

Set the Harmony A3 transmitter for compatible hearing aids, then choose how your hearing aids will receive the Auracast broadcast.

First: Open Advanced settings in the Firmware Update Tool. Select Advanced, set Audio Mode to Hearing Aid Compatible, and apply the settings.

Choose how your hearing aids connect

Auracast hearing aids

Join from your hearing-aid app or brand guide.

Choose your brand → You can hear music from your phone through your hearing aids You can switch your hearing aids to “T” or “MT”
Not sure about T or MT?

Look for a T or MT setting in your hearing aid app or paperwork. If you cannot find one, ask your hearing care professional.

Choose a brand

ReSound Danalogic Oticon Jabra Starkey NuEar Widex Cochlear Beltone Bernafon Philips Phonak Fortell

Requires: Your exact hearing-aid model supports Auracast. If unsure, check its app or official guide.

Other ways to listen

Choose the receiver that matches your hearing aids.

You can hear music from your phone through your hearing aidsUse Aura C

Aura C receiver plugs into a USB-C phone

Aura C phone hearing aids

  1. Plug Aura C into a compatible USB-C phone.
  2. The phone sends the broadcast to hearing aids already connected by Bluetooth, MFi, or ASHA.

Aura C does not pair directly with hearing aids.

Set up Aura C →

You can switch your hearing aids to “T” or “MT”Use AuraCoil or AuraClip

Switch to T or MT. The neckloop sends the broadcast to your hearing aids.

Quick help

Fix common problems

Need more help?

Our support team is here for you.

Contact Support

Was this helpful?